GILKA.
Tutorial

Espresso grind size for a portable espresso machine

A grind setting is not a property of the coffee, it is a property of the coffee plus the machine pushing it. Change the machine and the number changes with it — which is why the setting that worked on a café grinder produces a 12-second gusher in a portable one.

Gilka Coffee EditorialPublished Updated 5 min read
Short answer

Hold three numbers instead of one setting: 18 g in, 36 g out, 25–32 seconds. Grind fine enough that the shot reaches 36 g near the end of that window, then adjust one variable at a time — dose first, grind second. A portable machine with a fixed 9 bar chamber usually needs a finer grind than a pump machine at the same dose, because the pressure profile is flat rather than ramped.

Key takeaways
  • Grind is a response to resistance, not a recipe: fix dose and yield, then move grind until the time lands in the window.
  • Portable machines with fixed pressure typically want one to two steps finer than a 9 bar pump machine at the same basket.
  • A hand grinder's click size is the real limit on dialling in; know how many microns one click moves before you blame the machine.
  • If the shot time is right and the cup is still thin, the problem is usually temperature or channeling, not grind.

The three numbers, not the setting

Most grind advice fails because it hands you a number out of context. A grinder setting means nothing without the dose it was paired with, the basket it went into, and the machine pushing water through it.

So hold three numbers instead:

  • 18 g in — the dose, weighed, not scooped.
  • 36 g out — the yield, weighed in the cup.
  • 25–32 seconds — the time from first drop to the end of the shot.

Those three describe a shot. Grind is the dial you turn to hit them. When the time lands inside the window at that dose and yield, the grind is right for that coffee on that machine today. Tomorrow it may not be: humidity, bean age and basket temperature all move the number.

Why a portable machine sits at a different grind

Two geometry facts change the requirement.

Pressure arrives differently. A pump machine ramps from zero to 9 bar over several seconds. That ramp is gentle on the puck: flow builds while the bed settles. A regulated gas chamber at 9 bar is at 9 bar immediately, so the first water hits a dry, unsettled bed at full force. The same grind that ramps cleanly on a pump machine can channel in a chamber machine — hence one to two steps finer, so the bed resists long enough to settle.

The bed is shallower. Most portable baskets hold 16–20 g in a narrower, shallower cylinder than a 58 mm commercial basket. Resistance scales with bed depth, so per millimetre the puck needs to be tighter. Shallower bed plus same pressure equals faster flow at the same grind.

Add the third factor that nobody mentions: thermal mass. A portable machine is small and cools fast. A cold basket pulls heat out of the first millilitres of water, the water gets thicker (viscosity rises as temperature falls), and flow slows in a way that looks like "the grind changed". It did not. Preheat first, then judge the grind.

Starting points by device class

These are working ranges, not standards. Treat them as the first shot of the day, then move.

Device class Typical dose Grind relative to a 58 mm pump basket Expected time to 36 g
Chamber / gas-pressure machine, 9 bar fixed 16–18 g 1–2 steps finer 26–32 s
Lever portable, manual force 14–18 g roughly equal 25–35 s (force-dependent)
Pressurised basket portable 14–18 g 1–2 steps coarser 20–30 s
Pump portable with pre-infusion 16–18 g roughly equal 25–32 s
Moka pot (not espresso, for reference) 15–20 g much coarser 3–5 min total

If your machine's basket is pressurised — a small spring-loaded valve in the base — grind matters far less, because the valve, not the puck, sets the pressure. That is why cheap portables "work" with any coffee. It is also why they cannot produce a real 9 bar extraction: the puck never resists, so the water finds channels.

Move one step at a time

A dial-in procedure that converges instead of oscillating:

  1. Fix dose. Weigh 18 g. Do not change it for the rest of the session; dose changes both resistance and headspace, which doubles the variables.
  2. Pull one shot at the current setting. Record time and yield.
  3. Too fast (under 22 s, sour, thin): grind one step finer.
  4. Too slow (over 35 s, or chokes): grind one step coarser.
  5. Correct time, wrong taste: leave the grind alone. Change temperature or distribution, not the grind. This is where most people ruin a good setting by chasing a taste problem with the grinder.
  6. Write the setting down with the coffee name and the date. Fresh coffee changes over ten days; a log tells you whether the shift was the beans or your memory.

One step per shot. Two steps at once on a stepped hand grinder can move 40–60 microns, which is frequently the entire range between a gusher and a choke.

The hand grinder is usually the bottleneck

Portable espresso lives or dies on grind consistency, and consistency is where cheap hand grinders fail. A ceramic burr set with loose tolerances produces a wide particle distribution: fines that clog and boulders that pass water. The shot then runs fast and tastes both sour and bitter, and no grinder setting fixes it because the problem is the spread, not the average.

What to look for, in order of effect:

  • Conical steel burrs with a stable axle. Axle wobble is the defect that matters.
  • Step size, stated in microns. If a manufacturer cannot tell you what one click moves, that is the answer.
  • Zero retention, or close to it. A gram of yesterday's coffee in the chute ruins a 18 g dose.
  • Adjustment while running — being able to move the burrs under load makes dialling in far quicker.

Espresso-capable hand grinders generally start around the price of a mid-range portable machine. If that sounds like a lot for a travel kit, consider that the grinder determines the ceiling of every shot you will ever pull with that machine.

When the grind is not the problem

Four failures that look like grind problems and are not:

Symptom What it usually is What to do instead of grinding
Time right, cup thin and hollow Brew temperature too low Preheat chamber, basket and cup; start with water just off the boil
Time right, sour and harsh together Channeling from an uneven bed Level the grounds, tamp flat, check the machine is level
Shot gushes then stalls Basket overloaded or underfilled for its rating Weigh the dose against the basket's stated capacity
Same setting, wildly different times day to day Stale coffee or grind retention in the chute Fresher beans, purge a gram before dosing

The full dial-in sequence, including how to move from a new bag to a repeatable shot, is in brewing tutorials. If you want the pressure side of the same question — why a flat 9 bar behaves differently from a ramped profile — that is in pressure in espresso extraction.

Sources and further reading
  1. Specialty Coffee Association — brewing and extraction standards — https://sca.coffee
  2. Barista Hustle — espresso dialling and puck resistance — https://www.baristahustle.com
  3. Coffee grinders and burr geometry, general reference — https://en.wikipedia.org/wiki/Coffee_preparation
GILKA
EDITORIAL

Gilka Coffee Editorial

Technical writing from the Gilka Coffee engineering team. We publish brewing parameters, pressure and gas-budget calculations, and machine design notes. Where a number is an estimate or a first-principles calculation rather than a measurement, we say so in the text.

Questions

Frequently asked

What grind size should I start with for a portable espresso machine?
Start at the fine end of what your grinder calls espresso — the same setting you would use for a pressurised basket on a home machine — then adjust by time. There is no universal micron number: the same coffee at the same grind runs differently in a chamber machine, a lever machine and a pump machine. Use 18 g in, 36 g out, 25–32 seconds as the target and let the grinder find it.
Why does my portable machine need a finer grind than my home espresso machine?
Two reasons. A fixed-pressure chamber delivers 9 bar from the first drop with no ramp, and the puck is usually shallower with a smaller diameter, so the same flow needs more resistance per millimetre of bed. If your home machine ramps up over six seconds, that ramp is doing work your portable machine never gets.
Is pre-ground coffee acceptable in a portable machine?
It works, but you lose the main variable. Espresso pre-ground for a supermarket basket is typically coarser than a portable machine wants, so the shot runs fast and tastes sour and salty. If you must use pre-ground, buy it ground for espresso, keep it sealed, and expect the best results within a week of grinding.
How many clicks should I move the grinder at a time?
One step, then taste and time the shot. Two clicks at once on a stepped hand grinder can jump 40–60 microns, which is often the whole difference between a 22-second shot and a choked one. Write the clicks down; a notebook beats memory after the third coffee.
Does humidity change the grind setting?
Yes, and it is the most common reason a setting that worked last week now runs fast. Humid air makes grounds clump and static-charge, which changes how they pack. Adjust by taste on the day rather than chasing a fixed number across seasons.
For the machine

9 bar that does not need to ramp.

A regulated gas chamber holds pressure from the first drop, so the puck sees the same number for the whole shot.